axial silastic guard junction standard rectifier voltage range 50 to 1000 volts 6a05s thru 6a10s current 1.0 ampere e-mail: sales@cnmic.com web site: www.cnmic.com features low coat construction low forward voltage high forward surge current capability high temperature soldering guaranteed: 260/10 secods.0.375 (9.5mm)lead length mechanical data case: transfer molded plastic epoxy: ul94v-o rate flame retardant polarity: color band denotes cathode end lead: plated axial lead, solderable per mil-std-202e method 208c mounting position: any weight: 0.06ounce, 1.7 grams maximum ratings and electrical characteristics ratings at 25 o c ambient temperature unless otherwise specified single phase, half wave, 60hz, resistive or inductive load for capacitive load derate current by 20% symbols 6a05s 6a1s 6a2s 6a4s 6A6S 6a8s 6a10s units maximum repetitive peak reverse voltage v rrm 50 100 200 400 600 800 1000 volts maximum rms voltage v rms 35 70 140 280 420 560 700 volts maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 volts maximum average forward rectified current 0.375 (9.5mm) lead length at t a = 60 i (av) 6.0 amps peak forward surge current 8.3ms single half sine wave superimposed on rated load (jedec method) i fsm 250 amps maximum instantaneous forward voltage @ 6.0a v f 0.95 volts t a = 25 10.0 maximum dc reverse current at rated dc blocking voltage t a = 100 i r 500 a maximum full load reverse current, full cycle average 0.375 (9.5mm)lead length at t l =105 i r(av) 500 a typical junction capacitance (note 2) c j 100 pf typical thermal resistance (note 1) r ja 10 /w operating junction temperature range t j -55 to +150 storage temperature range t stg -55 to +150 notes: 1. thermal resistance from junction to ambient at .375 (9.5mm)lead length, pbc.mounted with 1.1 1.1 ( 30mm 30mm)copper pads . 2. measured at 1.0mhz and applied reverse voltage of 4.0v dc 0.052(1.3) 0.048(1.2) r-6s dimensions in inches and (millimeters) dia. dia. 0.280(7.2) 0.270(6.8) 0.360(9.1) 0.340(8.6) 1.0(25.4) min. 1.0(25.4) min.
axial silastic guard junction standard rectifier voltage range 50 to 1000 volts 6a05s thru 6a10s current 1.0 ampere e-mail: sales@cnmic.com web site: www.cnmic.com 1.0 fig.2-maximum non-repetitive peak 100 t jjmax 50 20 10 j t =100 c characteristics 8 5 2 300 200 100 1 0 c u r r e n t , ( a ) p e a k f o r w a r d s u r g e 10 number of cycles at 60 hz 8.3ms single half sine-wave (jedec method) =t forward surge current fig.4-typical reverse derating curve fig.1-typical forward current 150 175 125 75 100 50 0 025 a v e r a g e f o r w a r d c u r r e n t , ( a ) 10 fig.3-typical instantaneous forward characteristics ambient temperature, ( c) j t =25 c 80 40 60 100 1.0 0.1 20 0.01 0 ( m a ) percent of rated peak reverse voltage,(%) 100 1.4 j t =25 c 1.2 1.0 0.8 0.6 1% duty cycle pulse width=300us 1 0.1 ( a ) ( a ) 1000 100 instantaneous forward voltage,(v) fig.5-typical junction capacitance 10.0 1.0 4.0 0.1 10 reverse voltage,(volts) tj=25 c f=1mhz c a p a c i t a n c e , ( p f ) i n s t a n t a n e o u s f o r w a r d c u r r e n t , i n s t a n t a n e o u s r e v e r s e c u r r e n t , 1.61.82.0 140 120 2.0 3.0 4.0 5.0 6.0 60 60 hz resistive or inductive loads group plane 1" x 1" copper surface area recommended p.c. board mounting 100 1000 20 rating and chracteristic curves 6a05s thur 6a10s 250
|
